Ceramic Tube / Ceramic Rod / Ceramic Plate / Ceramic Valve / Ceramic Plunger / Ceramic Pump Manufacturer
Focus on Alumina / Zirconia ceramic parts R&D and production
+86 -181 2297 4730
Ceramic Tube / Ceramic Rod / Ceramic Plate / Ceramic Valve / Ceramic Plunger / Ceramic Pump Manufacturer
Focus on Alumina / Zirconia ceramic parts R&D and production
+86 -181 2297 4730
Moble: +86 18122974730
Phone: +86 746 3386888
Email: admin@cerampart.comSkype: +86 18122974730Wechat: +86 18122974730Precision Ceramic Pin Round Gauge
The ceramic pin gauge has longer life cycle than steel pin gauge, and the ceramic is non-conducting material, so it can be in electricity fields.
Meanwhile, the ceramic pin gauge is free from corrosion, it can be handled with hands don’t require special maintenance or rust prevention treatment.
Technical Parameters
| Size | Length | Class 0 | Class 1 | ||
|---|---|---|---|---|---|
| Tolerancce | Roundess | Tolerance | Roundenss | ||
| 0.2mm~0.99mm | 40mm | ±0.5μm | 0.3μm | ±1μm | 0.8μm |
| 1.00mm~10.00mm | 50mm | ±0.5μm | 0.3μm | ±1μm | 0.8μm |
| 10.01mm~20.0mm | 50mm | – | – | ±1.5μm | 1.5μm |
Tips: avaible in stocks part of above, and can be customized,please contact us: admin@cerampart.com
The way to use pin gauge
1.Use pin gauge: Hold the Measured parts by left hand, hold the pin gauge by right hand, put the pin gage into the measured round hole vertically.
Attention, don’t overpower, unwise, it will damage the pin gauge
Or make the measurement data is not accurate.
2.Choose pin gauge, according to the hole diameter of the measured parts on the drawings, firstly choose the smallest pin gage within the diameter range.
For example, if the hole diameter is 3.00+0.005mm, you should choose the 2.950 pin gauge,
If the 2.950 pin gauge cannot put into the hole, please choose a smaller one.
3.The reading of the pin gauge: the precise reading is as the pin gauge show.
4. After using, the pin gauge should be in place and properly kept.
High voltage and Insulator
High frequency insulating ceramics have small dielectric constant, low dielectric loss, high mechanical strength, high dielectric strength, insulation resistance and thermal conductivity.Dielectric constant up to 10; Electrical resistivity up to 10∧14 Ohm.cm at 20°C ;Dielectric strength up to 20 kV/mm...
| · Flexural strength | · Chemical resistance | · Electrical insulation | · Corrosion resistance | · Dielectric strength |
| · Wear resistance | · Temperature resistance | · Thermal conductivity | · High voltage | · Hardness... |
|
|
Al 2O 3 |
ZrO2/Y2O3 | ZrO2/MgO | MgO | SiC | Si3N4 Reaction sintered | Si3N4 Hot pressed | ALN |
| Physical properties | ||||||||
| Density (g/cm3) | 3,9 | 5,9 | 5,75 | 3,58 | 3,2 | 3,27 | 3,29 | 3,26 |
| Molecular weight (g/mole) | 102 | - | - | 40,4 | 40,1 | 140 | 140 | 41 |
| Maximum service temperature air (°C) | 1700- 1800 | 1500 | 1000 | 2200 | 1500 | 1200- 1500 | 1100- 1600 | 1000- 1800 |
| Mechanical properties | ||||||||
| Hardness (Mohs) | 9 | - | - | 5,5 | 9 | - | - | 7 |
| Modulus of elasticity (GPa) | 300-400 | 200 | 200 | 250-300 | 420 | 170-220 | 280-310 | 318 |
| Poisson's ratio | 0,25 | - | - | 0,18 | 0,14 | 0,25-0,26 | 0,27 | 0,25 |
| Fracture toughness (MPa.m1/2) | 2-3 | 7-13 | 6-10 | - | 2,5-3,5 | 3,5-5 | 6,1 | 4,5 |
| Electrical properties | ||||||||
| Dielectric constant | 9-10 | - | - | 9-10 | - | 10 | 10 | 9,2 |
| Electrical resistivity at 20°C (Ohm.cm) | >10 14 | 10 13-10 14 | >10 10 | - | 10 2-10 6 | >10 7 | 10 12- 10 15 | >10 14 |
| Dielectric strength (kV/mm) | 10-20 | 9 | 2-10 | - | - | - | - | 15 |
| Thermal properties | ||||||||
| Specific heat (J/K/kg) | 900 | 400-500 | 420 | 870-880 | 750 | 690 | 680-800 | 800 |
| Thermal conductivity (W/m/K) at 20°C | 26-35 | 2,2-3,2 | 1,5-2,5 | 40-50 | 63-155 | 9-30 | 15-43 | 180 |
| Coefficient of thermal expansion ( 10-6) from 20 to 1000°C | 8-9 | 10-11 | 5-16 | 10-13 | 4-5 | 3 | 3,3 | 4,4-5,3 |
| Melting point (°C) | 2050 | 2590 | - | 2800 | 2500 | 1900 | 1900 | 2200 |
|
Customization & Machining Service: As a ceramic parts manufacturer,us offer a wide of the ceramic specification,and customized&machinables. Get a Quote On Your Customized Now!! or up a files by EMAIL. Our Custom Capabilities: 1.High Purity Martoxid Powder 2.OEM Support, More Than 10 Technicians With 5-Year R&D Experience 3.35000 ㎡workshop, annual output could reach hundred million pieces. 4.All crafts are inspected strictly based on drawings,checked each month. 5.Best Service And Quick Delivery Via Fedex,DHL,UPS,TNT Etc. |
|
|||||||||||||||||||||||||||
FAQ
1. Monthly Capacity: 50,000-60,000 pcs;
2. Material: OEM or as per your suggestion;
3. Lead time: about 7-20 days, pls confirm the quantities required;
4. Incoterm: FOB, CFR, CIF;
5. Delivery Cost: It is determinated by the destination port;
6. Payment Term: PayPal; T/T; L/C.
7. Shipment: by sea, by air, by courier, by post, etc.
Feedback
1. For any query or doubt, please contact us firstly, we will update with you soon;
2. For any other satisfaction, please also feedback to us, which could improve our service better and better.
| For more information about ceramics parts,please contact our engineers in time >>> |
  |
Dynamic information Ceramic technology FAQ Ceramice exhibition
Ceramics quality Ceramics technical Ceramice after-sale Customer witness Patent certificate
Ceramic flange Ceramic bushing Ceramic plunger Ceramic pump valve
ADD：No. 21, Chuangxing Road, Shangsha Second Industrial Zone, Chang'an Town, Dongguan City
ADD：Southeast corner of the intersection of Changliu Road and Wangzhou Road, Qiyang High-tech Industrial Development Zone, Yongzhou City, Hunan Province, 426141,China
Mob：181 2297 4730 Tel：+86 746 3386888
Skype：+86 18122974730 Email：admin@cerampart.com
Mobile version
